Welcome to our blog.
Follow us here, by subscribing to the RSS feed at the top of the page.

Archive for November, 2010

The Nechville Helimount acoustic banjo is a breeze to set up and adjust to your liking, but I recently realized that there is a great need for more precise instructions for the more advanced players and those with very specific tone ideas in mind. When I am working in person, I always help people understand their banjo a little better, but I can’t do that with everybody, so here is my best shot at walking you through all the set up steps and adjustments that you can do on a Nechville banjo.

Let’s start with by making sure the head is set for the right sound and playability. Like any part of a banjo, The type of head is an important set-up choice. Something to think about before changing heads is what will the head do to the level of the playing surface of your head? For example, If you are going for the warmer sound of a relaxed head, you’ll benefit from using a high crown head, especially if you prefer to use a smaller bridge. The high crown allows the tone ring to push the head up higher in relation to the tension hoop so you can use a shorter bridge. If you go too tight with the high crown, the playing surface might get as high as the top of the tension hoop, which is not recommended.

Please don’t use low crown heads in a Helimount, unless you use it with an archtop tone ring. The low crown with a flat head tone ring may not give you enough room to thoroughly engage the thread of the flange ring with the thread of the Helimount, and it could become cross threaded. When replacing heads, always spin the flange ring in by hand and be sure it is level and nothing is preventing full mating of the threads.

I would also avoid certain specialty heads like Kevlar, and thick reflective heads: they usually don’t sound right, and their stiffness makes them difficult to use for the same reason as the low crown, unless they have been previously stretched out in another banjo. 5 Star and Lugwig white frosted on top plastic heads will work, but you’ll find the sound bright but one dimensional. I prefer the Remo standard heads for a bit more depth and full ranging response. The Renaissance translucent heads give a more organic or warm effect. Continue tightening your head to playing tension, place the bridge and tune it up.

There is a window of perfect tension for every banjo and it occurs when the head is around 90 on a drum dial. This corresponds to a head ringing when tapped with a G# note. You may need to add considerably more tension than you would expect to reach this optimum point. However it is possible to over-shoot the ideal tension. Beware if the sound gets sharp, cold and one dimensional. For more information on heads, see the Nechville News archive and look for anarticle, “Heading for Great Sound.”

Once you think the head is tight enough, Check  the neck bow. Hold down a tightened string at both ends of the fingerboard, and there should be a small distance from that string to the middle frets. I mean less than .01 or 1/100 of an inch of bow. That’s only a thick sheet of paper.  A 1/4″ nut driver is the tool of choice for adjusting the truss rod. Be sure you have one that is small enough to fit into the access hole on the peghead, (call Nechville if you need one).

With the proper neck Bow and tight head, now it’s time to install your favorite height bridge and check the action (my favorite is a 3/4″ radiused bridge). If you are satisfied with the action after reaching this step, great , it is time to skip to the next paragraph below.  If however the action is too low, you have a choice. Either install a higher bridge, tighten the head more, move the neck up to decrease neck angle, or do any combination of these 3 things to arrive at the best action. Consider how each adjustment affects the overall tone and whether it will take you closer or farther from your goal. When I mention these effects, note that the converse is also true (go the other way to remedy high action).

Taller bridge usually means more mass, increasing sustain, raising action, and giving the banjo the capability of being played with more volume, as long as the mass of the bridge is not muting too much. Keep the bridge under 3 grams and you should be OK. It is great to have an assortment of bridges, especially if you have several banjos.  Changing bridges at this point in the set up process is a good idea, because you can learn more about what size and weight bridge your banjo likes with the particular head tension and neck angle that you are starting out at.  Tighter Head means higher action, brighter and louder sound to a point, and generally a more focused and stable sound. If head barely yields to finger pressure, and reads over 92 on the drum dial, it might be too tight, in which case the bass response and body sound of the instrument can be lacking.Neck Angle is adjustable via the set screw on the bottom of the Heel. Loosening this screw loosens the neck, and the strings’ tension will pull the action higher.  Retighten the set screw firmly when you reach the proper action. Note, lowering action is best done with strings loosened, and the banjo placed face down in your lap while seated. You may need to re-lower and re-raise the neck angle a couple times to arrive at the perfect action. Be sure Allen screw is all the way tight and neck will not move when twisted.

Now that you have the head and action at playable levels, how does it sound? Perhaps it isperfect, but the point of this article is that as a picky player, you, like me will not be satisfied with perfect. We want special, magic, extraordinary. This lofty aspiration is what keeps my interest and is my continual aim. My builders are fantastic craftsmen who produce perfectly set up works of art. Part of my job is to give each banjo a personality of its own.  It is not an easy thing to teach, because every instrument is different and it is hard to predict what might make the instrument come alive. The following is a list of ideas, not a sequence asset out previously, but are optional techniques mentioned here for discovery.

The fun of this is that there is still room for surprises, Most of the adjustments I do have predictable results, But there are still times when I am surprised at how certain combinations of set up factors react. Are you looking for a gut rattling bass? Maybe the answer lies in finding the right bridge. conventional thinking would dictate a heavier bridge for enhanced bass, but maybe your ear is longing to hear the bright side of the banjo’s lower register. Perhaps a well crafted lighter bridge with a looser head would do the trick.

Do you want the overtones to enhance the experience of playing, not detract from it? Try moving the tailpiece forward and back, making the distance from the end of the tailpiece to the bridge different. Try Playing the strings on the wrong side of the bridge. Are they tuned to a common interval of the open string? I like the interval to match the second harmonic, or the 5th note of that string’s scale, but tuning it to other notes is possible with a Nechville tailpiece. First use thesmallest Allen wrench and back out the small setscrews until the tailpiece almost touches the frame. You’ll also have to loosen the lower set screw, but you can re tighten the lower set screw later if you want the strings to have the highest break angle over the bridge and add extra down pressure on the tailpiece. At this point, the tone should be sharp and snappy, but perhaps not full bodied enough for your liking. Now try exactly the opposite. Loosen the strings and tighten the small top tailpiece set screws. This moves the tailpiece back, decreases Break angle and lowersthe pitch of the sympathetic notes behind the tailpiece. As you move the tailpiece in and out, monitor the notes you hear when plucking behind the bridge. Try it with the larger bottom set screw barely snug, and have a friend help you monitor the sound as one of you tightens it. A piece of leather or felt between the strings behind the bridge would mute some of the high sympathetic vibration, perhaps yielding a “drier” tone.

Do you want the strings to jump to life with a mere touch? Try a Renaissance Head, and tighten it up a lot. Use a relatively light, but tall bridge, ie, 3/4″ 2.3 gram and moderate, (not too low) string action. Let the tailpiece tension off except for only slight down pressure. Then go aheadand try the down pressure by tightening the large Allen screw on the tailpiece, Try to find where you like it best.

Are you seeking easy, fast and clean playability ? That requires perfect fret level and perfect neck bow and perfectly shaped bridge. Given that there is an ideal neck bow shape, (not straight, but with perhaps .008 ” of bow) there is an optimum height for each string from the fingerboard as defined by the bridge’s shape. Of course with a radiused fingerboard, The bridge will need to have a similar shape, but too often people ignore the importance of the proper action of individual strings. The heaviest strings tend to get struck hard by the thumb, and so the 3rd and 4th strings need a bit more room to vibrate without hitting the frets. This means making the bridge higher in the middle than may be simply dictated by the neck’s radius. On a flat board, this would mean that a slightly radiused bridge would work better, allowing lower action on your 1st, second and 5th strings. However if you simply radius your bridge, you will be compounding the problem thatis already so common in banjos, and that is the 3rd string being sharp up on the higher frets. Make sure the 3rd string especially is compensated with a longer scale, and particularly if you have followed my advice and radiused the bridge more than the curve of the frets. The amount of compensation needed varies whether the bridge is sagging or higher on the 3rd string, but with the medium strings I use, (10,12,14,22,10), and a healthy radius, the 3rd string is set back about .080 from the other strings.

Do you want a banjo with perfect rich tone? Call Nechville for an assortment of heavy bridges. We will sell you several Enterprise bridges at a discounted price if you want to buy 3 or more. Start with a big bridge, and you can play with it by cutting deeper slots, and taking more ebony off the top. That will lower strings and perhaps change the harmonic content of the tone. You can spend time rounding the corners of your bridge, and thereby reducing the weight a little. Most of my best sounding banjos have bridges weighing between 2.4 and 2.8 grams.

The type of head and head tension are huge factors in controlling sound. A heavier, frosted head like a 5 star head tends to dry up the sound for less ringing and sustain. I have noticed the clear heads and black heads do have a bit of ringiness. When adjusting or installing a head, monitor how it sounds after every few twists of the Helimount wrenches. You might find a special tension that works even if it’s looser, but it is probable that you’d need to also raise action for play at looser head tension.

Once you find an ideal head tension for your banjo, mark the turning flange ring inside the banjo with a small piece of tape near the middle of the neck, And you will be able to return to that exact spot any time you choose. Your ideal tone may be different than mine, but given the ease of adjustment and armed with a little knowledge as to how to go about it, you will be ready to meet your next musical adventure.

Passionate Players

What keeps me interested in banjos is the passion of great players who hear a sound and remember it. Those people who play hundreds of banjos and try to understand what makes one sound better than another. One such player is Gabe Hircshfeld who shares my passion for great sounding instruments. Gabe has only been playing for a couple years, but he has an amazing ear and already outplays nearly everyone I know. I am honored that he recently chose to purchase a Nechville Banjo and we are currently working together to arrive at the optimal setup and options for his style and technique. We share a taste for high bridges, Wide necks, Mahogany wood, Radiused fingerboards and penetrating warmth in banjo tone.

Inspired by a recent conversation with Gabe, I decided to build a Mahogany Galaxy Phantom that would represent my favorite options and set-up parameters. Since Nechville banjos can be easily set up for high bridges with low action, That’s what I did.

The 3 gram bridge is 7/8″ tall. It has wide spacing and it is perfectly compensated for the string gauges. I chose to put on a custom set of strings. I use .010’s on the first and fifth and 12’s on the 2nd, but this time I lightened up the 4th string to a .020, and the 3rd to a .013. I think the slightly lighter pull on the tailpiece due to lighter strings lends to the mellowness without detracting too much from volume.

The wide neck also has wide frets that I believe helps hold the string in place solidly and lends to purity of tone. The radiused ebony fingerboard is done with Galaxy Abalone and Pearl inlay, and a tunneled 5th string adds convenience, playability and solidity of tone. I did the Snuffy Smith trick with a higher crown Remo head and the thicker frosting darkens the sound just slightly.

In combination with the head at medium tightness and the tall bridge, the notes roll off the instrument like giant pillow-y balls of sound. I removed the down pressure completely from the tailpiece and in fact raised the tailpiece up to the top of the bridge. My tailpiece lets the natural pull of the strings create the break angle for a nice open sound, but in this case I wanted less break angle than normal so I jacked the tailpiece up with the banjo’s built in pickup jack mounting bracket. Whenever possible I try to kill 2 birds with one stone like this. The high bridge and steep neck setback provides just enough break angle over the bridge for the sound to open up and allow a nice blend of subtle harmonics.

The energy can be felt through the resonator as sound processes through the unimpeded acoustical chamber of the Heli-Mount body. I can not imagine a better sound, but the Heli-Mount gives more choices of tonal character than any other banjo I know of. As for comfort, The tunnel is terrific the compound radius is perfect for the left hand, and makes picking easier for my right hand. The armrest is beveled exotic wood and helps make your body merge with the instrument in comfort. I can play it for hours in total comfort and the low action is as smooth as silk.

I have made similar banjos for people like Alison Brown, Noam Pickelney, Bela Fleck, Leon Hunt, Jake Schepps, and Adam Larrabee, who happen to be my favorite players.

If you can imagine yourself expressively and effortlessly making music this instrument, well it’s your lucky day. This banjo is my pick of the week, and it could be yours. Have total confidence in your purchase. I stand behind it with a 100% money back guarantee. This banjo is set up for a rich contemporary sound.

Alternate heads, tone ring options bridge heights and other components are interchangable, making this Nechville an enduring high value investment for you and your legacy. Interested parties may call me personally to arrange shipment and payment.

Tom Nechville